As the Ebola virus outbreak continues to run amok in West Africa, scientists are looking ahead to the possibly pivotal use of experimental drugs and vaccines against the disease. It will take months to test, produce and deploy the therapies. But researchers hold out hope that these products — even incompletely vetted — might help to turn the tide against an illness that has defied public health efforts to bring it under control.

Relays


relay symbol
Circuit symbol for a relay
Relay, photograph © Rapid Electronics
Relay, photograph © Rapid Electronics
Relays
working relay
Relay showing coil and switch contacts
A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions and most have double throw (changeover) switch contacts as shown in the diagram. Relays allow one circuit to switch a second circuit which can be completely separate from the first. For example a low voltage battery circuit can use a relay to switch a 230V AC mains circuit. There is no electrical connection inside the relay between the two circuits, the link is magnetic and mechanical.
The coil of a relay passes a relatively large current, typically 30mA for a 12V relay, but it can be as much as 100mA for relays designed to operate from lower voltages. Most ICs (chips) cannot provide this current and a transistor is usually used to amplify the small IC current to the larger value required for the relay coil. The maximum output current for the popular 555 timer IC is 200mA so these devices can supply relay coils directly without amplification.
Relays are usuallly SPDT or DPDT but they can have many more sets of switch contacts, for example relays with 4 sets of changeover contacts are readily available. For further information about switch contacts and the terms used to describe them please see the page on switches.
Most relays are designed for PCB mounting but you can solder wires directly to the pins providing you take care to avoid melting the plastic case of the relay.
The supplier's catalogue should show you the relay's connections. The coil will be obvious and it may be connected either way round. Relay coils produce brief high voltage 'spikes' when they are switched off and this can destroy transistors and ICs in the circuit. To prevent damage you must connect a protection diode across the relay coil.
The animated picture shows a working relay with its coil and switch contacts. You can see a lever on the left being attracted by magnetism when the coil is switched on. This lever moves the switch contacts. There is one set of contacts (SPDT) in the foreground and another behind them, making the relay DPDT.

The relay's switch connections are usually labelled COM, NC and NO:
  • COM = Common, always connect to this, it is the moving part of the switch.
  • NC = Normally Closed, COM is connected to this when the relay coil is off.
  • NO = Normally Open, COM is connected to this when the relay coil is on.
  • Connect to COM and NO if you want the switched circuit to be on when the relay coil is on.
  • Connect to COM and NC if you want the switched circuit to be on when the relay coil is off.

Choosing a relay

You need to consider several features when choosing a relay:
  1. Physical size and pin arrangement
    If you are choosing a relay for an existing PCB you will need to ensure that its dimensions and pin arrangement are suitable. You should find this information in the supplier's catalogue.
  2. Coil voltage
    The relay's coil voltage rating and resistance must suit the circuit powering the relay coil. Many relays have a coil rated for a 12V supply but 5V and 24V relays are also readily available. Some relays operate perfectly well with a supply voltage which is a little lower than their rated value.
  3. Coil resistance
    The circuit must be able to supply the current required by the relay coil. You can use Ohm's law to calculate the current:
    Relay coil current   =   supply voltage 
      coil resistance
    For example: A 12V supply relay with a coil resistance of 400ohm passes a current of 30mA. This is OK for a 555 timer IC (maximum output current 200mA), but it is too much for most ICs and they will require a transistor to amplify the current.
  4. Switch ratings (voltage and current)
    The relay's switch contacts must be suitable for the circuit they are to control. You will need to check the voltage and current ratings. Note that the voltage rating is usually higher for AC, for example: "5A at 24V DC or 125V AC".
  5. Switch contact arrangement (SPDT, DPDT etc)
    Most relays are SPDT or DPDT which are often described as "single pole changeover" (SPCO) or "double pole changeover" (DPCO). For further information please see the page on switches.

Protection diodes for relays

Protection diode for a relay Transistors and ICs must be protected from the brief high voltage produced when a relay coil is switched off. The diagram shows how a signal diode (eg 1N4148) is connected 'backwards' across the relay coil to provide this protection.
Current flowing through a relay coil creates a magnetic field which collapses suddenly when the current is switched off. The sudden collapse of the magnetic field induces a brief high voltage across the relay coil which is very likely to damage transistors and ICs. The protection diode allows the induced voltage to drive a brief current through the coil (and diode) so the magnetic field dies away quickly rather than instantly. This prevents the induced voltage becoming high enough to cause damage to transistors and ICs.


Reed relays


Reed Relay, photograph © Rapid Electronics
Reed Relay
Reed relays consist of a coil surrounding a reed switch. Reed switches are normally operated with a magnet, but in a reed relay current flows through the coil to create a magnetic field and close the reed switch.
Reed relays generally have higher coil resistances than standard relays (1000ohm for example) and a wide range of supply voltages (9-20V for example). They are capable of switching much more rapidly than standard relays, up to several hundred times per second; but they can only switch low currents (500mA maximum for example).
The reed relay shown in the photograph will plug into a standard 14-pin DIL socket ('IC holder').


Relays and transistors compared

Like relays, transistors can be used as an electrically operated switch. For switching small DC currents (< 1A) at low voltage they are usually a better choice than a relay. However, transistors cannot switch AC (such as mains electricity) and in simple circuits they are not usually a good choice for switching large currents (> 5A). In these cases a relay will be needed, but note that a low power transistor may still be needed to switch the current for the relay's coil! The main advantages and disadvantages of relays are listed below:
Advantages of relays: Disadvantages of relays:
  • Relays can switch AC and DC, transistors can only switch DC.
  • Relays can switch higher voltages than standard transistors.
  • Relays are often a better choice for switching large currents (> 5A).
  • Relays can switch many contacts at once.

  • Relays are bulkier than transistors for switching small currents.
  • Relays cannot switch rapidly (except reed relays), transistors can switch many times per second.
  • Relays use more power due to the current flowing through their coil.
  • Relays require more current than many ICs can provide, so a low power transistor may be needed to switch the current for the relay's coil.

Subscribe to: Posts (Atom)